|
YJ Large Bushing
|
DAYM02153
|
Poly bushings, manufactured by Daystar, are stocked in bulk quantities. In addition to fitting YJ springs, this bushing is used with the FO209 shackle hanger. Use in conjunction with either the DAY10007 or DAY10013 sleeve for proper installation. Bushing fits 1.5" diameter spring eyes or sleeves and has a .25" shoulder. Sold individually.
|
|
Bushing Sleeve, 9/16" Bolt
|
DAY10007
|
A bushing sleeve is inserted into poly bushings and then secured with a 9/16" bolt through the hanger bracket. It's primary purpose is to reduce wear on bushings. Sleeve is compatible with DAYM02221 YJ small bushing, DAYM02153 YJ large bushing, and DAYM02042 CJ large bushing. Bright zinc coating resists corrosion. Sold individually.
|
|
YJ Small Bushing
|
DAYM02221
|
Poly bushing, manufactured by Daystar, are stocked in bulk quantities. In addition to fitting YJ springs, this bushing is used with the FO206A shackle hanger and the FO205 frame sleeve. Use in conjunction with either the DAY10007 or DAY10013 sleeve for proper installation. Bushing fits 1.25" diameter spring eyes or sleeves and has a .25" shoulder. Sold individually.
|
|
Weld-on Spring Hanger Bracket, 2 1/2" Wide Springs
|
FO1900
|
Weld-on brackets for 2.5" width springs. Can replace stock factory Jeep brackets, and are useful in many other applications. The bracket measures 3" between the spring mounting holes, and will accept a shouldered bushing such as the DAYM02221 and a bolt sleeve (DAY10007). Use with a FO110 spring bolt to complete the installation.
Brackets are sold individually.
|
|
Spring Center Pin, 3/8" x 3.5"
|
FOCB12
|
Spring center pins are used when resizing the spring pack, for example when adding or removing a leaf, adding an axle shim, or using a relocator plate. They are also used as replacement parts for broken pins.
|
|
Poly Bushing Joint
|
FO2050
|
This poly bushing and sleeve joint is ideal for building inexpensive three link (also known as tri-link or wishbone) suspension systems. Two of these joints are used on the frame end of the link. They provide rigid control of side to side motion yet rotate freely up and down. The link would typically use a flex ball joint or Heim joint on the axle end.
The kit consists of a DOM sleeve with two poly bushings and an inner sleeve. The DOM sleeve is 1 7/8" in diameter. The inner sleeve accepts a 9/16" bolt. The assembled width of the joint is 2 5/8", making it directly compatible with standard control arm brackets.
The joint is pictured assembled and disassembled for clarity. Joints are sold individually.
|
|
CJ Large Bushing
|
DAYM02042
|
CJ large bushing, manufactured by Daystar, is stocked in bulk. It is a direct replacement for a CJ spring bushing. Bushing measures 1.5" in diameter with a 1/2" shoulder and accepts either the DAY10007 or DAY10013 sleeve. Sold individually.
|
|
Weld-in Stud Shock Mount
|
FO1020
|
This weld in mount is typically used as an upper shock mount on a crossmember. It fits into a 1/2" diameter hole drilled through a 2" crossmember or tube.
It can also be used as a weld on mount for sway bar disconnects on a front axle. It typically would be welded to the lip of a spring plate.
These mounts are sold individually.
New lowered price--this is a blowout special to reduce excess inventory.
|
|
CJ Small Bushing
|
DAYM02047
|
CJ small bushings, manufactured by Daystar, are stocked in bulk. The bushing is a direct replacement for CJ spring bushings but can also be used for a variety of applications. Bushing has a 1" diameter with .25" shoulder and directly accepts a 1/2" bolt. Sold individually.
|
|
Brake Hose Mount Bracket
|
FO1580
|
Mount bracket secures brake hose to a rigid surface such as a frame rail or axle tube. Accepts any of the female flare fittings on our hoses. Used in conjunction with a standard "C" clip for securing the hose.
|
|
Tube Adapter, 1 1/4"-12 RH
|
FO5716
|
This tubing adapter is 1 1/4"-12 right hand thread and accepts threaded rod, Heim joints or tie rod ends. Adapter welds into 1.5" ID tubing to form a control link. Sold individually.
|
|
Mount Tab, Frame Small
|
FO5301
|
Universal mount tab is welded to a flat surface such as a frame rail. Typically used in pairs, they form a mount for a shock, small control arm, or sway bar link. Drilled for 1/2" hardware.
|
|
Mount Tab, Shock
|
FO5303
|
Universal mount tab is welded to a curved surface such as an axle tube. Typically used in pairs, they are shaped to clear a shock absorber. Drilled for 1/2" hardware.
|
|
Flare Fitting, 3/8 Female
|
FOFM1032403
|
Inverted flare fitting secures brake hose to 3/16" diameter hard line. AN-3 fitting allows use with any of the universal hoses.
|
|
Anchor Shackle Tab, Weld On
|
FO7501
|
This shackle tab can be welded to any structural member and serves as a fastening point for a screw pin anchor shackle. Machined from 1" thick billet steel with an eye for 7/8" anchor shackles. Sold individually.
|
|
Mount Tab, Short
|
FO5309
|
This mounting tab is a short version of the FO5301. The primary application is mounting of a coilover shock. It measures 1 1/8" from the center of the hole to the weld surface. Hole is 1/2" diameter.
Tabs are sold individually.
|
|
U Joint, 1310 Series
|
DAN5153X
|
This U joint is the most commonly used U joint in driveshaft applications. It is a 1310 series joint used in standard and CV style shafts. This style includes a zerk fitting for lubrication of the joint.
|
|
Weld-on Stud Shock Mount
|
FO207
|
This mount is normally welded to the forward or trailing side of an axle tube as a lower shock mount. The upper shock mount is typically a stud on a crossmember, such as the FO1020.
This shock mount is sold individually.
|
|
Dana 44 Long Stud for High Steer Arm
|
FOD44LSTUD
|
These long studs are used with tall steering arms and spacer blocks on Dana 44 steering systems. Studs replace the shorter, OEM style studs so that additional thread is available to properly tighten the cones and nuts.
Studs are sold individually; typically three are required for an arm.
|
|
8 degree 2.5" Axle Shim
|
FO8.0
|
Steel shims allow correction of driveline angle problems on rear axles or caster problems on front axles. These shims bolt into the spring pack, and won't crumble as aluminum versions do. New spring center pins may be required for your spring pack.
This shim is 8 degrees by 2.5" wide. The mounting hole is 5/16" diameter and may be drilled out to fit other sizes.
Shims are sold in pairs.
|
|
6 degree 2.5" Axle Shim
|
FO6.0
|
Steel shims allow correction of driveline angle problems on rear axles or caster problems on front axles. These shims bolt into the spring pack, and won't crumble as aluminum versions do. New spring center pins may be required for your spring pack.
This shim is 6 degrees by 2.5" wide. The mounting hole is 5/16" diameter and may be drilled out to fit other sizes.
Shims are sold in pairs.
|
|
Contura Switch Body SPST One Light
|
WAY44305
|
CONTURA SWITCH BODY SPST ONE LIGHT
Similar To ARB Locker Switch
This is a Contura switch body for controlling electrical accessories and/or circuits. It is a on/off style, single pole single throw switch that has one light. Terminals are 1/4" spade lug connections.
This switch is used with any of the Contura switch caps found in other listings in this category. When used with our mounting panels found in this category, they can be assembled into a unified switch array. It?s the same series of switch that ARB uses for their lockers and when combined with those switches, offers an integrated appearance.
This is a switch body only, the cap is sold separately. Switches are sold individually.
|
|
Dana 44, 30 Spindle Service Kit
|
DAN706527X
|
This spindle service kit is a universal kit for spindles found on Dana 30 and Dana 44 and GM 10 bolt front axles. It includes a pocket bearing, V gasket, seal, and thrust washer for servicing one spindle.
|
|
Tube Adapter, 1 1/4"-12 LH
|
FO5717
|
This tubing adapter is 1 1/4"-12 left hand thread and accepts threaded rod, Heim joints or tie rod ends. Adapter welds into 1.5" ID tubing to form a control link. Sold individually.
|
|
4 degree 2.5" Axle Shim
|
FO4.0
|
Steel shims allow correction of driveline angle problems on rear axles or caster problems on front axles. These shims bolt into the spring pack, and won't crumble as aluminum versions do. New spring center pins may be required for your spring pack.
This shim is 4 degrees by 2.5" wide. The mounting hole is 5/16" diameter and may be drilled out to fit other sizes.
Shims are sold in pairs.
|
|
Creeper Joint, 1 1/4"-12 RH 5/8" Bolt
|
TG110759-K
|
These heavy duty rod ends are ideal for today's flexible suspension systems. Super strong, Creeper Joints will hold up to years of punishment. The outer shell is a single forged piece. The inner flex ball is made from 8620 tool steel and rides on high quality polyurethane bushings. Heavy-duty, hardened steel washers hold the joint together.
Creeper Joints are super flexible and allow for up to 40 degrees of movement when used with spacers. A threaded grease fitting is provided on top for lubrication. The flex ball is drilled for cross lubrication flow from the shell to the link mount bolt. Each joint includes a jamb nut.
This joint has 1 1/4" - 12 RH threading, accepts a 5/8" bolt and is 2 5/8" wide. Threaded portion is 3" long.
|
|
Contura Switch Cap Black w/Red Lens
|
WAY44352
|
Contura Switch Cap Black with Red Single Light
Similar To ARB Locker Switch Caps
This is a Contura series switch cap for use on the Contura switch bodies. It is a black soft rubber style cap with a single red lens.
This cap is used with any of the Contura switch bodies found in other listings in this category. It allows for a unified look for switch arrays including lights, on/off switches, winch control, and many other options. It?s the same series of switch that ARB uses for their lockers and when combined with those switches into an array of switches, it offers an integrated appearance.
This is a cap only and is used with the rocker switch bodies which are found in separately in this category. Caps are sold individually.
|
|
Banjo Fitting, 7/16"
|
FO7760304
|
Banjo fitting 7/16" bolts. AN-3 threading allows use with any of the universal hoses.
|
|
Banjo Fitting, 3/8"
|
FO77603
|
Banjo fitting 3/8" bolts. Also fits 10 MM banjo bolts. AN-3 threading allows use with any of the universal hoses.
|
|
Bushing/Sleeve Kit
|
FO2051
|
Bushing and sleeve kit includes the parts necessary to build an isolated mount point or control arm end. Kit includes an FO205 sleeve, 2 poly bushings, and 1 9/16" inner sleeve. Overall width is 3", making it compatible with many suspension components.
Kits are sold individually.
|
|
Dana 44, Dana 30 Ball Joint Set
|
DAN706116X
|
This kit contains upper and lower ball joints, with hardware, for use on a traditional style Dana 30 or Dana 44 front axle. These axles were found under Jeep CJs and most 1/2 ton trucks with a full spindle and locking hub design. Kit is manufactured by Spicer.
Please note that these ball joints DO NOT fit later style unit bearing axles, such as those found under Jeep YJs, XJs or TJs, or under Ford IFS trucks, or under later Dodge trucks.
This kit contains the parts to service one side of the axle.
|
|
Shackle Bar, 5"
|
FO2055
|
Shackle bars allow assembly of custom shackles were an application specific part is not available. Bars are drilled with 1/2" holes that can be enlarged for other sizes. Sold individually. Length is measured from centers of mounting holes.
|
|
Poly Bushing Joint, Large
|
FO2050A
|
This poly bushing and sleeve kit is a heavy duty version of our standard size part. It is ideal for building control arms for full size vehicles or high power vehicles that need superior axle control. It can also be used for an inexpensive wishbone link.
The kit consists of a DOM sleeve with two poly bushings and an inner sleeve. The DOM sleeve is 2 3/8" in diameter. The inner sleeve accepts a 5/8" bolt. The assembled width of the joint is 2 5/8", making it directly compatible with standard control arm brackets.
The joint is pictured assembled and disassembled for clarity. Joints are sold individually.
|
|
Shackle Bar, 4"
|
FO2054
|
Shackle bars allow assembly of custom shackles where an application specific part is not available. Bars are drilled with 1/2" holes that can be enlarged for other sizes. Sold individually. Length is measured from centers of mounting holes.
|
|
Creeper Joint, 1 1/4"-12 LH 5/8" Bolt
|
TG110762-K
|
These heavy duty rod ends are ideal for today's flexible suspension systems. Super strong, Creeper Joints will hold up to years of punishment. The outer shell is a single forged piece. The inner flex ball is made from 8620 tool steel and rides on high quality polyurethane bushings. Heavy-duty, hardened steel washers hold the joint together.
Creeper Joints are super flexible and allow for up to 40 degrees of movement when used with spacers. A threaded grease fitting is provided on top for lubrication. The flex ball is drilled for cross lubrication flow from the shell to the link mount bolt. Each joint includes a jamb nut.
This joint has 1 1/4" - 12 LH threading, accepts a 5/8" bolt and is 2 5/8" wide. Threaded portion is 3" long.
|
|
Tube Adapter, 3/4"-16 RH
|
FO5710
|
This tubing adapter is 3/4"-16 right hand thread and accepts threaded rod, Heim joints or tie rod ends. Adapter welds into 1" ID tubing to form a control link. Sold individually.
|
|
Mount Tab, Offset
|
FO5307
|
This mount tab features an offset mounting hole, making it ideal for mounting a shock just above the top of a frame rail. It allows you to use a slightly longer shock for improved suspension travel. Weld surface is 2.5" long, and the mount hole is located 1.25" from the weld surface. Hole diameter is 1/2".
Tabs are sold individually.
|
|
Tube Adapter, 7/8"-18 RH
|
FO5718
|
This tubing adapter is 7/8"-18 right hand thread for use with tie rod ends. Adapter welds into 1" ID tubing to form a control link. Sold individually. For Heim joints or threaded rod, use the FO5712, which is threaded 7/8-14 RH.
|
|
U Bolt 12x3.5x.625
|
FO6511
|
12" Long x 3.5" Inside Diameter x .625" Diameter
|
|
Mount Tab, Shock, 1.5" Tubing
|
FO5306
|
This mount tab is designed for use with 1 1/2" diameter tubing or similar size, that is typically used in shock hoops. The mounting hole sits farther from the tubing, making it suitable for large body shocks such as coilover shocks. Mounting hole is 1/2" diameter.
Tabs are sold individually.
|
|
U Joint, Dana 44 Axle
|
DAN5760X
|
This joint is used in Dana 44 front axles and some later model Dana 30 and 35 front axles. Newer style design has a stronger trunnion and sealed caps for greater reliability.
|
|
Tube Adapter, 7/8"-18 LH
|
FO5719
|
This tubing adapter is 7/8"-18 left hand thread for use with tie rod ends. Adapter welds into 1" ID tubing to form a control link. Sold individually. For Heim joints or threaded rod, use the FO5713, which is threaded 7/8-14 LH.
|
|
U Bolt Kit, GM Dana 44 Front
|
RS703
|
The U bolts in this kit fit a GM style Dana 44 front axle. The kit can be used for replacing worn or damaged U bolts on an early 70's GM truck, or it can be used when installing an upgraded axle in a different vehicle, such as a customized Dana 44 in a springover CJ.
U bolts are zinc plated. The kit includes one U bolt sized 3.65" x 9" x 5/8" diameter and three U bolts 2.78" x 7.75" x 5/8" diameter.
Kit ships as either a Rancho RS703 or Pro Comp 58201, depending on stock on hand.
|
|
Flare Fitting, 3/8 Male
|
FO1032403
|
3/8" flare fitting mounts directly to slave cylinder found on most drum brake applications for front axle applications. AN-3 fitting allows use with any of the universal hoses.
|
|
Jamb Nut, 1.25"
|
FO125JN
|
A jamb nut is used to lock a control arm at it's desired length and to prevent movement of the threaded rod within the coupler. This nut is 1 1/4"-12 RH threaded and can be used with the FO5702 Threaded Rod. Great for building custom control arms and other links.
|
|
Switch Body, ARB
|
ARB180209
|
ARB Switch Body
Used with ARB Compressors and Lockers
This switch body from ARB is for use in ARB's locking differential systems. It is used as the Front, Rear, or Compressor switch, and accepts all three of the switch caps. It can be used to replace damaged switch caps or for building your own control system.
This is the switch body only; the caps are sold separately in this category.
Switches are sold individually.
|
|
Banjo Bolt, 3/8-24x1
|
FO77503L
|
Banjo bolt is used to secure banjo fitting on brake hose to brake caliper. Bolt is 3/8-24 thread, 1" long.
|
|
Contura Switch Cap Black w/No Light
|
WAY44351
|
Contura Switch Cap Black with No Light
Similar To ARB Locker Switch Caps
This is a Contura series switch cap for use on the Contura switch bodies. It is a black soft rubber style cap with a plain cover, no light.
This cap is used with any of the Contura switch bodies found in other listings in this category. It allows for a unified look for switch arrays including lights, on/off switches, winch control, and many other options. It?s the same series of switch that ARB uses for their lockers and when combined with those switches into an array of switches, it offers an integrated appearance.
This is a cap only and is used with the rocker switch bodies which are found in separately in this category. Caps are sold individually.
|
|
Tubing Flange, 1.75" Tube
|
FO5304B
|
This tubing flange slips over a section of 1.75" diameter tubing and can then be welded into place as an intermediate mount point. The flange is 4.5" long by 2.75" wide with 3/8" mounting holes on 3" centers. Item is laser cut from 1/4" thick steel plate.
Flanges are sold individually.
|
|
Axle Bracket, Lower Right
|
FO5101R
|
Bracket welds to axle tube for lower mount on left side. It is sized for 3" diameter tube, can be easily modified for other sizes. Mounting hole accepts 9/16" diameter hardware. Bracket accommodates standard 2 5/8" joints. The bracket is angle 7 degrees to provide triangulation of the suspension. It is constructed of 1/4" steel.
|
